[GnomeMeeting-list] Re: Still there Re: Same Problem at http://mail.gnome.org/archives/gnomemeeting-list/2002-December/msg00263.html



> On Fri, 2003-05-30 at 18:07, Damien Sandras wrote:
> Hello,
> 
> How did you install GnomeMeeting?

Hello,
     I have installed gnomemeeting by the following steps.
*****************************************************************
At first untar the following files
Start at location where openh323,pwlib,gnomemeeting tar files are  found

STEP 1
  @ directory /home/murugesan/
  type
 tar -xvzf openh323_1.9.10.tar.gz
 tar -xvzf pwlib_1.3.11.tar.gz
 tar -xvzf gnomemeeting-0.94.1.tar.gz

Then do the following

STEP 2
 export PWLIBDIR="/home/murugesan/pwlib"
 export OPENH323DIR="/home/murugesan/openh323"

STPE 3
     cd pwlib
     make bothnoshared

After making type 

STPE 4
     cd /home/murugesan/openh323
     make bothnoshared

Type the  following after changing to gnomemeeting-o.94.1 directory

STEP 5  GOTO STEP 6 bcoz,
     ./configure --prefix="/home/murugesan/gmeet"
--with-ptlib-includes="/home/murugesan/pwlib/include/ptlib/"
--with-ptlib-libs="/home/murugesan/pwlib/lib/"
--with-openh323-includes="/home/murugesan/openh323/include/"
--with-openh323-libs="/home/murugesan/openh323/lib/"

You will have the following error
    checking for /home/murugesan/pwlib/lib//libpt.so... no
    configure: error: You need PTLib to enjoy GnomeMeeting
    So link the following files

STEP 6
    ln -s /home/murugesan/openh323/lib/libh323_linux_x86_d.a
/home/murugesan/openh323/lib/libopenh323.so
    ln -s /home/murugesan/pwlib/lib/libpt_linux_x86_d.a
/home/murugesan/pwlib/lib/libpt.so

STEP 6.a
     Again configure using the above configuration procedure.

Then type
STEP 7
     make
     make install.

STEP 8
      cd /home/murugesan/gmeet/
      $./gnomemeeting
*************************************************************
This is how I installed gnomemeeting.

    The problem at the site
 http://mail.gnome.org/archives/gnomemeeting-list/2002-December/msg00263.html
also occurs in my linux(9) system.
 
 How can I clear the error?
                               Murugesan N


> 
> Ps: you should really use the mailing list to ask your questions.
> 
> Le ven 30/05/2003 à 14:31, murugesan a écrit :
> > Hello sir,
> > 
> >          The problem still exists.
> > As per the instructions 
> > I changed the permissions as 
> > 
> >           $ chmod -R 4755 /etc/gconf/gconf.xml.defaults/
> > 
> > Then I typed 
> > 
> >           $ killall -9 gconfd-1
> > The error was 
> >           $ gconfd-1 : no process killed
> > So I typed
> >           $ killall -9 gconfd-2
> >           $ ./gnomemeeting
> > But the same problem exists 
> > 
> > For your information 
> > 
> >     1) No files named gconf_test* in my PC
> > 
> >     2) $ gconftool-2 --get-default-source
> >                outputted 
> >        xml::/etc/gconf/gconf.xml.defaults
> > 
> >     3) $ ./gconftool-2 --get 
> > /etc/gconf/gconf.xml.defaults/apps/gnomemeeting/gconf_test_age
> > 
> >                outputted 
> > 
> >       No value set for            
> > `/etc/gconf/gconf.xml.defaults/apps/gnomemeeting/gconf_test_age'
> >                                   
> >                                Murugesan N
> > > On Fri, 2003-05-30 at 17:24, Damien Sandras wrote:
> > > Hello,
> > > 
> > > Le ven 30/05/2003 à 13:36, murugesan a écrit :
> > > > Hello sir,
> > > >          The problem at the site
> > > > http://mail.gnome.org/archives/gnomemeeting-list/2002-December/msg00263.html
> > > > also occurs in my linux(9) system.
> > > > After typing 
> > > 
> > > > 
> > > >   $./gconftool-2
> > > >     --get             
> > > > /etc/gconf/gconf.xml.defaults/apps/gnomemeeting/gconf_test_page
> > > > 
> > > 
> > > It is not gconf_test_page, but gconf_test_age
> > > 
> > > > Actually I first installed gnomemeeting.It worked at first. Then I
> > > > installed Openh323Gatekeeper.Only after installing Gatekeeper The above
> > > > mentioned error was reported.
> > > > 
> > > 
> > > That can't be related. Perhaps you are running old gconf 1 applications
> > > that can give trouble to gconf 2 applications. Just do a killall -9
> > > gconfd-1 and try again.
> > > 
> > > > How can I clear the error?
> > > > 
> > > >                                       -- 
> > > >                                       murugesan <murugesan visolve com>




[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]