Le mercredi 08 décembre 2004 à 16:35 +0530, Ashutosh Sharma a écrit : > Hello, > > Thanks for the help. Well about the firewall related settings then I > inspected but no firewall is enabled. But I tried from some other > Windows Machines..And it works but the problem comes related to > accepting the call from other user. Well let me explain the senario that > I did:- > I have one Linux M/C (FC2) with GM, OpenH323, Open MCU installed in my > PC. My PC is on a domain that is having all other computers on Windows. > I did following steps :- > > 1). Firstly I tried Simple NM--> GM call with listen_port =1740 in > GnomeMeeting by gconf-editor. It gave me the error like: "The person you > called is not able to accept NM calls". That is right b'cas as you told > that NM can accept only for 1720 port. > I tried GM-->NM also with the same settings but I got the message on NM > side that "Could not connect to remote host". Well I tried all the > combinations as: > h323:10.100.112.8:1720,h323:10.100.112.8:1740,h323:10.100.112.8 from my > GM. But the same result. > > 2). Now I tried the NM-->GM with listen_port=1720. The audio/video > worked fine.But when I tried GM--> NM then I got the same message that > "Could not connect to remote host" on GM side. > > Well can you please explain me what is happening here. I am in a totally > confused state. > It means that the IP you are calling is not reachable from your computer or that the port is closed. You could try : telnet 10.100.112.8 1720 and see if it works, I guess it won't. Firewall on the Netmeeting side? > 3). listen_port = 1740. I started openmcu as: openmcu -c -d > as a daemon. It started by showing me the PID and creating an end point. > THen from NM I did:- 10.100.112.25 (Address of MY PC where GM and > OpenMCU are installed). Then I got on console that a room101 has been > created and on NM side I got a message Box like : "waiting for a > response from 10.100.112.25" > Now from GM I tried h323:10.100.112.25:1720 then I got the message > that Remote user is busy. But when I tried h323:10.100.112.25:1740 then > It showed me "connected" on GM side but on NM side the same dialog > "waiting for a response from 10.100.112.25" was there although I got the > message on console that 10.100.112.25 joined the Conference Room101 > And in the same senario if I do GM-->NM by h323:10.100.112.8 then it > shows me connected on GM side but nothing happens on NM side. > Firewall? > 4). Now the settings were like this: listen_port = 1720 > started openmcu -c -d .. started successfully > Started NM .. ok . > But when I started GM then I got the message like this: > > "You will not be able to receive incoming calls. Please check that > no other program is already running on the port used by GnomeMeeting." > Then I pressed OK. Obvious, if openmcu is listening on the same port then that is logical that GnomeMeeting can not use it > And now if I do : h323:10.100.112.8 THen I got connected to the NM user > without the functionality of OpenMCU and was able to have audio/video. > But As I tried through openmcu as > From NM: call to: 10.100.112.25 --> "waiting for a response from > 10.100.112.25" > Then from GM:- URL:h323:10.100.112.25 --> Connected ...But nothing > was happening and on NM side the same dialog box regarding waiting was > there. > > Well I am totally confused with this whole senario. And I need some help > on openmcu functionality and H.323 end points. > > Thanks, > Regards, > Ashutosh Sharma > > > > On Wed, 2004-12-08 at 14:55, Damien Sandras wrote: > > Le mercredi 08 décembre 2004 à 11:11 +0530, Ashutosh Sharma a écrit : > > > Hello All, > > > > > > I am having some questions related to GM,NM and OpenMCU. Well I tried > > > the GM-->NM call... Audio and Video works fine. But for NM-->GM call the > > > error message comes that "The person can't accept NetMeeting calls". > > > > Are you sure you don't have : > > - a firewall on the local machine > > - another program than gnomemeeting blocking port 1720 and preventing > > to be called > > > > > > > Also how can I use OpenMCU to connect more than one GM and NM clients. > > > > Just call openmcu from as many clients as you need > > > > > Also what is the significance of the listen port 1740/1720 in the GM > > > when we tweak via gconf-editor. > > > > > > > If you change 1720 into 1740, GM will listen for incoming calls on port > > 1740 and you will have to specify that port in the URL. However, pay > > attention to the fact that Netmeeting doesn't accept to call remote > > endpoints that do not listen on port 1720 and are using another port. > > > > > > > Thanks in advance.. > > > Regards, > > > Ashutosh > > > > > > > > > _______________________________________________ > > > GnomeMeeting-list mailing list > > > GnomeMeeting-list gnome org > > > http://mail.gnome.org/mailman/listinfo/gnomemeeting-list > > _______________________________________________ > GnomeMeeting-list mailing list > GnomeMeeting-list gnome org > http://mail.gnome.org/mailman/listinfo/gnomemeeting-list -- _ Damien Sandras (o- GnomeMeeting: http://www.gnomemeeting.org/ //\ FOSDEM : http://www.fosdem.org v_/_ H.323 phone : callto:ils.seconix.com/dsandras seconix com
Attachment:
signature.asc
Description: Ceci est une partie de message =?ISO-8859-1?Q?num=E9riquement?= =?ISO-8859-1?Q?_sign=E9e?=